...

How to plant an ax on an ax

This post provides readers with step-by-step instructions on how to plant an ax on an ax. Firstly, it educates on the importance of proper preparation with the selection of the right axes and selection of appropriate soil. Secondly, it explains the process of planting the ax with the help of diagrams, focusing on the importance of adequate spacing, with suggestions for preparing the appropriate soil and ensuring proper watering. Finally, it focuses on the advantages of planting an ax, including how it is a great way to recycle an ax and sustainably grow more trees. In a nutshell, this post comprehensively explains the importance of proper preparation and technique when planting an ax on an ax.

The wooden ax, as the weakest part of the tool, always wears out faster than a metal ax. He begins to dangle, and this is not just an inconvenience in work, but also a danger. We will tell you how to correctly change the hatchet and attach an ax to it.

Most often, birch is used to make a hatchet, as a tree is quite hard, but at the same time affordable and easy to process. Beech and ash are also used. The workpiece should be brought to the size you need so that the handle sits comfortably in your hand.

Important! The wood for the ax must be well dried. If the workpiece is made by hand in winter, then be sure to keep it warm for two to three days before the nozzle..

Of course, ready-made hatchets are most often bought. The price can range from 20-80 rubles for the simplest polished workpieces up to 3500 rubles for a hand-carved ax. For the preparation of firewood and an independent nozzle, of course, simple, but high-quality hatchets are suitable, in which case there is no need to pay for expensive options.

How to plant an ax on an ax

To attach an ax to a hatchet, you need the blanks themselves, five wedges, a hacksaw for wood (some craftsmen use a hacksaw for metal so that the width of the grooves for the wedges is minimal), a marking pencil, a rubber or wooden hammer (mallet), a piece of gauze and epoxy.

Important! The wedges should be made of a harder wood than the ax. You can take larch, oak, beech (if the ax is made of birch).

One wedge will be wide, four will be narrow. To process them and fit the ax to the ax, you will also need a grinder.

How to plant an ax on an ax

At the first stage, the outline of the ax nozzle is outlined on the hatchet, lines for the cuts of the grooves are highlighted.

Important! The ax should sit as tightly as possible on the ax, it is necessary that it protrude from the eyelet not less than one centimeter.

The protruding piece of the hatchet after the racking will be of a larger diameter, this will allow you to rigidly fix the metal part of the tool and avoid the risk of its dismounting during operation.

Experts advise to slightly bore the eye of the ax before the attachment under the cone from the side of the ax. A file is used for this. This ensures that the ax does not slip off after wedging..

How to plant an ax on an ax

The cuts in the hatchet should be 2/3 of the depth of the eyelet. Do not forget that one centimeter protruding above the eye should be added to this indicator. The cuts are made carefully with a hacksaw according to the markings applied. The direction of the fibers of the wedges is parallel to the narrowing so that they do not break upon impact.

How to plant an ax on an ax

Before placing the blade on the haft, apply two to four layers of gauze soaked in epoxy resin, which will perfectly fill all the irregularities. The protruding, excess pieces of gauze are cut off. The wedges are also lubricated with epoxy before being inserted into the cut grooves. It is advisable to pour the resin into the grooves themselves, by about a quarter. This is done after the ax is inserted..

You can hammer in wedges with a rubber or wooden hammer, saw off the protruding parts. The main danger at this stage is to split the hatchet by driving the wedges too hard..

How to plant an ax on an ax

Epoxy resin has many useful properties. First, it acts as a reliable glue. Secondly, it is resistant to water and therefore does not allow the ax to get wet. Thirdly, the epoxy does not shrink, and after drying it forms a strong monolith that fixes the ax to the ax..

Epoxy hardens in warmth for a day, but it is safer to wait a week before using an ax.

How to plant an ax on an ax

We admit that it is somewhat more difficult to put an ax on a hatchet than to sharpen it. There are other ways, besides the one described by us, for example, with three wedges, with a cross. As for the basic requirements for the blanks and the tool itself, follow GOST 1400-91 “Hatchets for construction axes”.

Rate the article
( No ratings yet )
Recommender Great
Tips on any topic from experts
Comments: 4
  1. Serenity

    How does one go about planting an ax on top of another ax? Are you referring to stacking them vertically or attaching them somehow? I’m curious to understand the purpose or technique behind this. Could you please provide more context or clarification on what you mean by planting one ax on another?

    Reply
    1. Ava Anderson

      Planting an ax on top of another ax typically refers to the technique of stacking them vertically. This practice is commonly seen in log splitting or tree chopping. The purpose behind this technique is to achieve a greater impact force when striking a log or tree by adding the weight of the second ax. It helps to increase the efficiency and effectiveness of the chopping motion. The process involves aligning the heads of both axes and positioning the top ax just above the handle of the lower ax. By striking the top ax, the force is transmitted through to the lower ax and ultimately to the target, creating a more powerful impact.

      Reply
      1. Leo Moore

        Planting an ax on top of another ax is a technique used for log splitting or tree chopping to increase impact force and efficiency. By stacking the axes vertically and aligning their heads, the weight of the top ax adds force when striking the target. This method allows for a more powerful impact by transmitting the force through the axes. It is a common practice in woodcutting to make the chopping motion more effective and quicker.

        Reply
  2. Clara Murphy

    Is it possible to plant an ax on another ax? If so, what is the correct technique to achieve this? I’m intrigued by the idea and would love to experiment with it. Any tips or guidance would be greatly appreciated!

    Reply
Add comments