Beeline router setup. Do-it-yourself guide to connecting a wifi Beeline do-it-yourself router with video

The content of the article

• Configure a router for Beeline
• Configuring a Beeline DIR-300 router
• Configuring the Asus Beeline router
• Configuring TP-Link Router for Beeline
• Configuring a Zyxel Keenetic router for Beeline

Network access is provided by many providers, but Beeline is considered one of the popular options. The company provides 4G mobile Internet or home connection. You can set up a connection through a proprietary modem or a router of another company to get Wi-Fi coverage. Configuration may vary due to device model.

Configure a router for Beeline

When using several computers at home, the task of setting up Wi-Fi becomes relevant. Wireless internet is especially convenient if you have modern smartphones, tablets or laptops. Beeline settings through the router can be carried out automatically or manually, it depends on the model of the device. As a rule, when concluding a contract, a wizard comes home to help create a connection. If the Wi-Fi installation was carried out later, or the device was replaced, then you will have to reconfigure the connection.

For each device, there is an instruction for setting parameters for proper operation, but there are points that are the same for each case. For example:

• connect the wire (cable) to the router;
• connect the device through a second wire to a computer;
• configure the device (drive the address of the Beeline router, set the type of connection, set a password and protect the connection).

Configuring a Beeline DIR-300 router

There are several popular models of devices that are used by most customers. Few people take options without Wi-Fi, because, as a rule, for the sake of it, a device is purchased. The Beeline dir router is configured in two stages: physical connection, browser connection control. First you need to make sure that the latest firmware is installed for the network card. This is more true for owners of older computer models. The configuration is further carried out as follows:

1. Unpack the device, connect the power supply, the cord to the connector with the inscription “WAN”. Connect the second cord to one of the additional inputs and lead to the computer.
2. Next, configure the connection in the Start menu. Go to “Control Panel” here click on “Network Management Center …”. Click on “Adapter Settings”. Put a line on the Internet protocol version 4, then click “Properties”.
3. Make sure that the items with automatic issuance of IP and DNS servers are active.
4. Next, go to the internal interface. To do this, in any browser, type “192.168.1.1” into the site address field. A login / password form will be displayed to enter the admin panel. To go inside, you must enter the word “Admin” on both fields. These are factory access options, if they do not fit, then they have changed. You can reset the values ​​by holding the Reset button on the device. Hold for about 10 seconds.
5. When entering the internal interface, select “Configure manually.” Next, go to the “Network” tab, click “Add”.
6. Choose connection type – L2TP, dynamic IP.
7. In the appropriate fields, enter the issued Beeline login, password.
8. Check the boxes next to “Keep Alive” and “Connect automatically.” Click “Save”.
9. Click “Save” again. Next, an automatic connection will occur. To learn about the correct operation of the network, just go from your phone to any site.

Configuring the Asus Beeline router

Another popular manufacturer of the device is Asus. There is no program on the disk for automatic connection to the network, so you have to do everything manually. Configure the Asus Beeline router as follows:

1. Connect the device to power, network and computer.
2. Open a browser, write in the address bar of the site 192.168.1.1, press enter.
3. To access, specify the password and login “admin”.
4. In the internal interface, click on the “Advanced Settings” tab, select “Wan”. Next, specify the following data: “Connection Type” – “L2TP”, “Get the WAN IP automatically” – “Yes”, “Connect to DNS Server automatically” – “Yes”, “VPN Server” – “tp.internet.beeline. com “. In the fields with login / password, indicate the access issued by the provider.
5. To enable Wi-Fi, go to the “Network Map”.
6. A table appears on the right for quick wireless configuration. You need to configure it as follows: “Wireless name” – indicate / invent the name of the home network, “Security level” – “WPA-Auto-Personal”, “WPA Encryption” – “TKIP + AES”. On the line “WPA-PSK key” write the password for Wi-Fi. Click the “Apply” button.

Configuring TP-Link Router for Beeline

This is a popular model due to the installation wizard, which is able to connect to the network independently. As a rule, a disk is sold with the device on which the program is located. You just need to connect the router to the computer, insert the CD and run the application. If the connection does not open, you need to do everything yourself. The TP-Link router for Beeline is configured as follows:

1. After connecting the device, go to the browser, type “192.168.1.1”, press “Enter”. Enter the username / password “admin”
2. Open the “Network” tab and the “WAN” item.
3. Indicate the type of connection “L2TP”, enter the login / password that your provider (Beeline) issued, the IP server – “tp.internet.beeline.ru”.
4. Indicate automatic connection (“Connect Automatically”), the MTU size is 1400. Click on the “Save” button.
5. To enable Wi-Fi networks, go to the “Wireless” section, click on “Wireless Settings”.
6. Create a network name, specify the region “Russia”, the channel and mode – “automatically”. Click the “Save” button.
7. Next, go back to the “Wireless” section, click on “Wireless Security”.
8. Here, activate the item “WPA-PSK / WPA2-PSK”, then everything is in the “automatically” mode. Create a password for the connection, click “Save”.

Configuring a Zyxel Keenetic router for Beeline

Some users prefer Zyxel. The physical connection of the router is carried out in the same way (wire to the WAN connector and the second to the computer’s network card). The intranet configuration of the Beeline keenetic router is as follows:

1. Type in the browser line 192.168.1.1.
2. Enter “admin” as login / password.
3. Go to the “Internet” section, click on “Connection”.
4. Specify the following values ​​in order: choose any name of the Internet center, configure the IP parameters and obtain DNS automatically, check the box for answering ping requests and enable UPnP. Click on “Apply”.
5. Next you need the “Authorization” tab. Do not check the first item, the protocol must be L2TP, the server address is tp.internet.beeline.ru, write out the issued access in the username and password lines. Save changes.
6. To activate Wi-Fi, open the “Wi-Fi Network” section, the “Connection” section.
7. Check the box to enable the access point. Think of a network name, the SSID field should remain empty, the standard is 802.11g / n. The following two points should be in the “auto-select” mode, then leave everything as is. Click on “Apply”.
8. Click on the Security tab. Set authentication WPA-PSK / WPA2-PSK, type of protection – TKIP / AES, format – ASCII. Think of a password for access. Click Apply.