How to hem pants on a typewriter or manually. How to properly shorten and hem pants with your own hands

The content of the article

• How to hem men’s pants manually
• How to hem pants on a sewing machine
• How to hem knitted trousers on a typewriter
• How to hem sports pants on a typewriter
• How to hem jeans pants

The situation when the trousers sit perfectly, but are not comfortable with the length, is common. For fast-growing children, parents buy pants and overalls with a margin. To shorten the legs, you can contact the studio, paying money. Having dealt with the technology, it is easy to do it yourself – manually or with a sewing machine.

How to hem men’s pants manually

Not every house has a sewing machine, but you can sew pants with your own hands using threads and a needle. The secret method is also used in classical products, where the hem should not be noticeable. It is important to consider:

• the bottom in the finished form is ironed from the inside only along the edge;
• measuring the necessary length is carried out on a person or using the finished product;
• when sweeping, the seam of the leg and the bent part must be combined.

How to hem pants manually with a blind stitch? First you need to measure, note how much to cut. Then, you must:

• combine trousers;
• make a mark on the length of one leg with a centimeter tape on both sides, near the arrows;
• using a ruler, draw lines from these points at right angles, connect them with a smooth curve;
• measure down 4 cm, draw a line;
• fasten the legs with pins, combining the side and inner seams;
• trim with two scissors at once.

Process the bottom of the leg so that it does not open, better with an overlock. In the absence of a sewing machine, this is done by crocheting or sheathed manually. Following actions:

• bend inwards at the mark;
• pin with pins;
• iron the bottom of the leg from the inside;
• hem with a hidden seam, grabbing 2 threads on the leg and hooking them at the processed edge of the hem in 5 mm increments;
• turn out;
• unplug arrows first, then place the firmware inside the iron.

How to hem women’s pants in length? There are no special differences in technology. It is customary to leave 3 cm for feminine products instead of 4 in the male version. Light fabrics are often used for sewing ladies’ pants, so a method using adhesive tape called a spider web is suitable. He will help those who are not friends with the needle. The shortening technology is as follows:

• do preparatory operations, as with manual binder;
• the bent and steamed edge is pushed back;
• laying a web-braid;
• ironed.

How to hem pants on a sewing machine

The process will be much faster if there is a sewing machine. How to hem pants in this case? The peculiarity is that when steaming the hem from the inside, an imprint may appear on the front side, which cannot be removed on some materials, so only the very edge of the bottom of the leg should be ironed. How to shorten pants on a sewing machine? There are two ways..

In the first, to hem, you will need a special foot for a blind seam. The preparatory stage, as when bending manually. Further, it is necessary:

• turn the trouser leg with a bent and chipped edge to the front side;
• put a trouser leg under the needle under the foot of the sewing machine;
• at the same time turn down, on the front side, the bent edge – under the foot there will be an edge processed by overlock and bending of the material;
• hem a seam on a typewriter.

The second method is performed by a straight line. How to shorten the pants in this case? They do this:

• 5 cm are measured from the length line;
• cut off;
• process the edge;
• pins along the fold line;
• ironed;
• turn out on the front side;
• lay 4 cm from the bottom, draw a line;
• a line is made on the front side at this mark;
• iron the edge of the legs.

How to hem knitted trousers on a typewriter

The peculiarity of working with knitwear – when sewing, threads can be tangled, torn, and the material wrinkles. To eliminate these troubles, it is advisable to use a special foot to help promote tissue. In modern machines there are special lines for knitwear, but you can also hem a simple machine if you use needles with a rounded end. It is only necessary to choose the right thread and adjust their tension. For a better stretch of the fabric, you can glue the web-tape or put a strip of paper.

How to steal knitwear trousers? To do this, do not recommend the line with two needles because of the low strength. The operations are carried out in the sequence:

• measure the size of the leg;
• lay 2 cm, cut off;
• the edge is treated with an overlock;
• bend with pins;
• flashing from the inside on the overlock line;
• make another seam with a distance of 5 mm.

How to hem sports pants on a typewriter

Since sweatpants are often made from knitted fabrics, they are also stitched using the same technology. Such clothes in some cases have decorative stitches or inserts made of a material of a different color. If there are similar elements on sweatpants, you can shorten them not from below, but where the decorative seam goes. This is also true in cases where the bottom leg is elasticated or has cuffs..

If zipper is sewn into the side of the pants, it is opened and steamed up to the line of the new pants length. Five centimeters are laid aside for a hem and cut off. Further, the work is performed as follows:

• fasten and iron the fold line;
• pins are removed;
• the excess end of the lightning at the bend is swept at an angle;
• the unnecessary part is cut off;
• sweep the edge with a hem 1 cm – folded zipper should be inside;
• stitch the seam along the bottom of the leg and vertically – in the place where the lock is located.

How to hem jeans pants

Jeans buyers have to deal with the shortening problem – not all models have the necessary size. Hemming has its own characteristics. Often they do double bending, but on such a thick fabric it is difficult to do. Therefore, they recommend:

• perform work on a sewing machine intended for that;
• use thick special threads and needles;
• place the hem where the decorative seam passes, tap with a hammer;
• the length must be put aside on each leg along the inner seam, and not from the bottom – the legs can be of unequal length.

Measure the length of the product so that the pants touch the floor at the back. Then the following actions are performed:

• draw a dimension line on the fabric;
• lay 4 cm on a double hem;
• turn inside out;
• fold at the bend, stab with pins;
• bend the free edge by a centimeter;
• sweep;
• flashing from the wrong side;
• ironed.