Recommendation points
- Choosing and buying new entrance doors
- Dismantling of old entrance doors
- Installation of a new front door
- Installation of locks
- Installation of platbands
If you decide to replace the old front door in the apartment with a metal one, then it is not necessary to call specialists. A home master is quite capable of doing this. In this photo instruction, we will tell you about dismantling an old door and how to install a metal door with your own hands..
So, first, let’s figure out what tools and supplies we need to replace the front door:
- Screwdriver or screwdriver.
- Crowbar or pry bar.
- Jigsaw or hacksaw.
- Puncher.
- Level.
- A hammer.
- Anchors.
- Wood screws.
- Polyurethane foam.
- Entrance door with box and locks.
All types of work that we have to do can be divided into five stages:
- Choosing and buying new entrance doors.
- Dismantling the old front door.
- Installation of a new front door.
- Installation of locks.
- Installation of platbands.
Choosing and buying new entrance doors
Today on the market, doors are presented in a wide range. Often, door manufacturers offer to purchase an entrance door together with a frame and locks, which is very convenient. Entrance doors are mostly offered in two standard sizes: eighty and ninety centimeters wide. Therefore, before buying a new entrance door, measure the dimensions of the entrance opening..
Our choice fell on a metal entrance door with MDF coating. This door is completely complete: box, door itself, platbands, peephole and locks.
Dismantling of old entrance doors
The door, which we have to dismantle, led from time to time. It does not hold the porch poorly and cannot provide the proper level of heat and sound insulation.
We begin to dismantle the front door by removing the outer platbands. In this case, they are fixed with self-tapping screws, so we use a screwdriver. Remove the upper platband, then remove the side outer platbands.
After removing the outer platbands, we also dismantle the inner.
Then we remove the old door from its hinges. Why it is necessary to open it and lift it up.
After the front door has been removed from the hinges, remove the door frame.
We begin to dismantle the box from the bottom. Then we remove the side pieces, and finally remove the top bar. To facilitate the dismantling of the old wooden box, in case the bars are difficult to dismantle, it is necessary to saw them and dismantle them in parts, prying them off with a pry bar.
After dismantling the old door frame, we have a clean opening.
Installation of a new front door
First, we prepare a new door. We set it on the level on wooden blocks.
We put the door on them.
We expose the box using a level.
We set the level on both sides.
After the door has been leveled, proceed to its installation. For this we need a hammer drill with a drill for concrete and four anchors.
The door frame has four special holes through which we make holes in the wall with a puncher to a depth equal to the length of the anchor.
Important! After all the holes for the anchor have been made, check everything again with a level.
We insert anchors into the holes. If necessary, we help with a hammer.
We fix the anchors with a screwdriver.
Installation of locks
After the door frame is installed, it’s time to move on to installing the locks.
To do this, we put on the door handles.
Then we take the core and use the key to put it in the “open” position.
We insert the core into the lock and turn the key to the “closed” position.
Using the bolts, we adjust and set the lock, after which we proceed to fixing the handles.
After the new front door and the lock are installed, proceed to the installation of platbands.
Installation of platbands
Install the platbands in the following order:
- Side trims.
- Upper casing.
For installation, we need metal screws and a screwdriver.
Platbands installed.
Now we take the plugs and close the anchor holes with them.
We close the self-tapping screws on the platbands with plastic plugs.
We fill the space between the box and the wall with mounting foam around the entire perimeter.
Advice!If during operation the doors make a creak or “go” tight, then in 99% of cases the problem lies in poorly lubricated bearings or a ball in the hinge. To solve this problem, we recommend removing the door from the hinges, lubricating the bearing with machine oil and reassembling everything in the reverse order..
Can you please provide step-by-step instructions with accompanying photos on how to install an entrance metal door? I’m interested in ensuring that I install it correctly and would greatly appreciate any guidance you can provide.
I apologize, but I am unable to provide photos as I am a text-based AI. However, I can provide you with step-by-step instructions to install an entrance metal door:
1. Measure the door frame opening to ensure the metal door will fit properly.
2. Remove the old door, including the hinge plates and hardware.
3. Clean the door opening and remove any debris.
4. Place the metal door in the opening and ensure it fits evenly.
5. Insert shims between the door frame and the wall to provide stability.
6. Use a level to ensure the door is plumb and level in all directions.
7. Secure the metal door by attaching the hinge plates to the door frame with screws.
8. Install the doorknob, deadbolt, and any additional hardware according to the manufacturer’s instructions.
9. Check the door’s functionality by opening and closing it.
10. Install weatherstripping around the edges to provide a seal.
11. Paint or finish the metal door according to your preference.
Please note that these instructions are a general guideline, and it is essential to follow the specific instructions provided by the manufacturer of your metal door.