8 tips for straightening your hair with an iron for a long time, smoothly and without harm

The content of the article

• Smooth clean and dry hair only
• Comb thoroughly before straightening
• Apply thermal protective agents
• Adjust the temperature correctly
• The shorter the hair, the smaller the width of the iron
• Start straightening the back of the head
• Separation into strands up to 2 cm
• Clean the appliance regularly

If you often use an iron to straighten your hair, then you have come across a situation where the curls do not want to straighten out or after only an hour curl again. The reason is improper handling of the device or in it..

Smooth clean and dry hair only

Thermal exposure to wet hair leads to serious damage to its structure, and after cooling completely, the strands still become wavy. It is better to dry the curls in the air, without using a hairdryer. If this is not possible, dip a towel after washing, and only then treat with 90% hot air.

Before using the straightener, the strands must completely cool after the hairdryer..

When shampooing, use shampoos and conditioners with a smoothing effect. When straightening hair with an iron at home, use moisturizers so that, due to the high temperature of the hair straightener, they do not become dry and brittle, like straw.

Comb thoroughly before straightening

Before straightening your hair with an iron, you need to comb it thoroughly so that there are no tangled knots and creases. This is especially true for owners of curly curls.

Use a comb in tandem with an iron: brush along the length, followed by a straightener. Between heat exposure, comb all the strands and keep them in tension during processing so that the curls straighten. The result will be more stable than when straightening without a comb.

The comb itself should be clean, wash it and degrease it first. If this rule is not observed, creases are formed during installation. In the place of the nodule, under the influence of a hot device, the structure will be broken.

In the best case, the hairs will split, in the worst – they may fall out.

Apply thermal protective agents

Frequent use of a straightener and hair dryer harms the hair structure. To prevent this, use special sprays, mousses, serums. Ironing straighteners protect hair from moisture loss, nourish it and neutralize the effects of ultraviolet radiation.

Pay attention to the temperature range indicated on the packaging of the thermal protective product..

Wait until the strands are completely dry before treatment. If using a hair dryer for faster drying, apply a protective substance after shampooing.

Adjust the temperature correctly

An iron, heated to 360-450 ° C, dries out the hair and makes it lifeless. It is best to work at 150-200 ° C and choose a temperature based on the type and condition of the hair. If they are healthy and thick, and you use a high-quality thermal protective agent, then the device can be heated to 200 ° C, if thin – not higher than 150-165 ° C.

If the roots are thicker, stronger, and the tips are thin, dry, different temperature conditions are needed to straighten them. To create a basal volume, heat the device to maximum, but treat the main length at a lower temperature.

Wait for the device to warm to the desired temperature, and then proceed with styling. If the planes warm up unevenly, then the strands will begin to curl in a few hours.

The shorter the hair, the smaller the width of the iron

Devices have different plate widths. For long hair, the working surface of the iron should be wide, and for short – narrow. The thicker the hair, the wider the rectifier sheet should be. Recommended ratio of length, density of hair and the width of the plates ironing:

• to the shoulders – 2-2.5 cm;
• to the shoulder blades, but not very thick – 2.5-3 cm;
• thick, slightly below the shoulders – 3-4 cm;
• long and thick – from 5 cm.

Start straightening the back of the head

The result of straightening directly depends on the order in which the strands are processed. Straightening the strands will be easier if you start the procedure from the back of the head. This helps create a uniform volume throughout the head. Lock the excess strands so that they do not accidentally fall into the iron.

Processing exclusively from the roots to the ends, and not vice versa.

After the nape, straighten the strands on the crown. Do not hold the device for a long time in one place, make movements with the same speed and pressure. Straightening the basal area, lift the hair up. Lastly, treat the strands around the face.

Separation into strands up to 2 cm

If you take too large a strand when working with the iron, the temperature effect will be uneven. The strands that are in the middle will not warm up and will not smooth out. It is necessary to carry out an ironing in one place several times, and this worsens the condition of the hair structure. It is better to divide the strands into the thinnest – no more than 2 cm.

Such processing will take more time, but the result will be close to ideal.

Clean the appliance regularly

After using the iron, pollution remains on its surface: residues of cosmetics, dust, grease. For high-quality and safe installation, use only a cleaned appliance. For treatment, medical alcohol or special disinfectants, which are offered by manufacturers of cosmetics, are suitable. Wipe down cooling surfaces of the iron by dampening a cotton pad or cotton cloth with a small amount of cleaning agent.